Search results

• Toga Spyder Log
  test_family (tests.test_font.FontTests) ... ok test_measure (tests.test_font.FontTests) ... ok
  32 KB (4,574 words) - 09:47, 2 August 2018
• Tulsa electronics club
  * http://www.affiliatedelectronics.com/ 8901 East Admiral Place, TULSA OK * http://www.graybar.com/ 12535 East 52nd Street, TULSA OK -- fiber optic cable, Stahlin [[enclosures]], etc.
  5 KB (855 words) - 08:44, 16 December 2025
• Controlino Notes
  ** set xxx yyy => cannot be valid but no error message, no error may be ok
  1 KB (217 words) - 10:11, 2 February 2017
• Setup Toga with Spyder
  which seemed ok, I can now run Spyder
  2 KB (326 words) - 07:00, 9 August 2018
• Debugging the Smart Terminal
  ...nothing back, you have your reasons to believe that the arduino is working OK. Or you are getting data back but it is gibberish.
  2 KB (348 words) - 05:48, 13 September 2019
• Two Axis Stepper Controller
  ok ...is changed by a lot. In any case the arduino should finally respond with "ok". Each motor has its own position, speed and acceleration settings. You c
  6 KB (973 words) - 11:22, 6 March 2025
• Linux Commands On Pi
  # ok to have 2
  2 KB (300 words) - 17:55, 8 December 2016
• FreeCad: Viewing and Navigating a Model
  ...unsure what I am looking at in the model, or if the zoom and position are ok. I find a reset is useful:
  3 KB (498 words) - 11:54, 12 December 2019
• 3D Printer Kit
  ...old it in place. It is a bit of a reach to the controller board but seems ok.
  2 KB (401 words) - 06:07, 26 January 2018
• Arduino SIG Project - Russ
  ...n the terminal and Arduino. Not very slick yet, but basic principal seems ok.
  3 KB (530 words) - 14:16, 27 January 2017
• Playing With PIC Pack
  Ok, reads fine. rest read ok, -- did not open sample code, need to go back and do this.
  8 KB (1,149 words) - 11:41, 26 April 2010
• Wearable computer project
  Ok, so I ''can'' say a bit more about this now. I'm planning to create my own
  4 KB (651 words) - 09:03, 1 April 2012
• Raspberry Pi Stretch - 2018 Tricks
  Ok this is an old one. Lots of directions say edit a file with the command li
  4 KB (668 words) - 05:55, 1 February 2018
• GreenHouse Monitor Program
  |ok |ok
  11 KB (1,818 words) - 08:30, 25 August 2022
• Pi Setup Dec 2018 - Stretch
  ok: ok:
  12 KB (1,783 words) - 13:24, 20 November 2019
• Python Smart Terminal Technical
  * a<cr> microcontroller aquires data and responds "ok" ...in objects that are almost all GUI then using "from Tkinter import *" is ok but better is: "import Tkinter as Tk"
  13 KB (2,196 words) - 14:50, 18 February 2020
• Minimig display compatibility
  | LCD 19" TFT Monitor || Samsung || SyncMaster EX1920 || Yes || Yes || 50Hz OK testd in TURBO CHAMELEON 64 (Minimig CORE TC64)
  5 KB (711 words) - 04:17, 26 May 2013
• Python Smart Terminal Technical Details
  ...e other way around. Queues are supposed to be thread save so we should be ok so far. Thread processing is quite localized in the code so you should be
  6 KB (1,052 words) - 12:11, 28 August 2022
• Input protection
  1N4148 etc. They seemed to work ok, but the fast rising ...what current will result. Some references suggest that a few ma should be ok, check you data sheet perhaps it will have some info. Raise the resistance
  11 KB (1,709 words) - 17:33, 14 October 2016
• Programming the Device
  *The programming have been completed, press OK the close the message box
  6 KB (801 words) - 22:29, 25 April 2012

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)