Difference between revisions of "Salvage Parts and Sources"

From OpenCircuits
Jump to navigation Jump to search
Line 272: Line 272:
 
|
 
|
 
Ribbon Cables and Sockets
 
Ribbon Cables and Sockets
 +
|
 +
Yes.  I ( [[russ_hensel]] ) have found a bunch or applications that may not be obvious, I will write it up soon, or contact me.
 +
|
 
Computer
 
Computer
 +
<!--------------------------------->
 +
|-valign="top"
 +
|
 +
Sockets: DIP
 
|
 
|
Yes
+
Yes I ( [[russ_hensel]] ) I sometimes cut these up in various ways and epoxy to .1 inch perf. board to get special sockts for LED arrays....
 
|
 
|
*where
+
Computers and many other components.
 
<!--------------------------------->
 
<!--------------------------------->
 
|-valign="top"
 
|-valign="top"
Line 300: Line 307:
 
Often useful, often can find specification from part number.
 
Often useful, often can find specification from part number.
 
|
 
|
*where
+
Audio equipment, TV's
<!--------------------------------->
 
|-valign="top"
 
|
 
Sockets: DIP
 
|
 
Yes
 
|
 
*where
 
 
<!--------------------------------->
 
<!--------------------------------->
 
|-valign="top"
 
|-valign="top"
Line 323: Line 322:
 
Transistor: Small Signal  
 
Transistor: Small Signal  
 
|
 
|
Some use, but may be hard to identify which are useful.
+
Some use, but may be hard to identify which are useful as many use house part numbers.  A few hours work gave me a couple of bucks worth of parts [[russ_hensel]], probably not worth it.
 
|
 
|
*Many different devices but usually not computers.
+
Many different devices but usually not computers.
 
<!--------------------------------->
 
<!--------------------------------->
 
|-valign="top"
 
|-valign="top"
 
|
 
|
Transformers – Misc.
+
Transformers Inductors – Misc.
Maybe
 
TVs Audio Receivers.
 
 
|
 
|
Yes
+
Test with ohm meter and audio oscillator.
 
|
 
|
*where
+
TVs Audio Receivers.
 
<!--------------------------------->
 
<!--------------------------------->
 
|-valign="top"
 
|-valign="top"
 
|
 
|
 
Transformer Flyback transformer
 
Transformer Flyback transformer
 +
|
 
Yes for high voltage – but can be dangerous.
 
Yes for high voltage – but can be dangerous.
TVs
 
|
 
Yes
 
 
|
 
|
*where
+
TV's
 
<!--------------------------------->
 
<!--------------------------------->
 
|-valign="top"
 
|-valign="top"
 
|
 
|
 
Transformer: Line to Low voltage  
 
Transformer: Line to Low voltage  
 +
|
 
Useful for making power supplies.
 
Useful for making power supplies.
Audio equipment particularly receivers.
 
 
|
 
|
Yes
+
Audio equipment particularly receivers.  Computer perifferals (sp ) but not computers.
|
 
*where
 
 
<!--------------------------------->
 
<!--------------------------------->
 
|-valign="top"
 
|-valign="top"

Revision as of 07:12, 29 January 2008

Another page in early construction by russ_hensel, this attribution will be removed when I am "finished" with the page.


Parts -- Where to Find Them

What Comments Where

Beeper

Yes

  • Mother boards
  • Microwave ovens

Caps: Electrolytic

You can get tons of these from most devices, usually marked with voltage and capacitance, they are pretty much ready to use.

  • Many different devices.

Case

Can be very useful, may want to replace or overlay the front panel. Sometimes use a different side of the case as a new front.

Crystals

Are the frequencies useful, can you figure out how to drive them?

  • Computer devices
  • Radio receivers
  • Diodes: Full Wave Bridges and Power

Yes

Many different devices.

Diodes: Small Signal

Usually have leads that are so short that they are not worth bothering with

  • --

Headers and Jumpers

Useful as headers or to adapt parts to prototyping boards. You can also often find cables with plugs that plug into the headers very nicely. Also true of RC hobby servos.

Computer mother boards.

Fans: Small

Yes

  • where

Heat Sinks

Yes

  • where

Infra Red Receiver Useful for IR remote control projects. Any equipment with with a remote control

Yes

  • where

Jacks: RCA Phono

Yes

Audio equipment and many computer mother boards.

Jacks: Miniature Phono Jacks

Yes

Audio equipment. Sometimes on computer mother boards

Jacks: USB

Yes

  • Computer mother boards

Jacks: 9 Pin ( serial )

Often useful particularly if you harvest cables from old mice.

  • Computer Mother boards

Jacks: Key Board Jacks

Yes

  • Computer Mother boards

Jacks: Key Board Jacks

May be useful particularly if you harvest cables from old keyboards.

  • Computer mother boards

Laser

xxxxxxxxxxxxx

  • Printers, cd rom, dvd players

LED: visible

Very, sometimes leads too short, but usually ok.

  • Many devices, often on a control panel separate from the main circuit board

LED: Infra Red

Usefully for IR remote control projects.

  • Remote controls.

LCD Displays

Useless, too hard to find out the specs.

  • where

Low Voltage Power Supplies

Yes

  • Computers. Wall warts that may come with devices. Some other devices have power supplies as separate components.

Motors: DC Yes VCRs, Tape Recorders

Yes

  • where

Motors: Stepper

Printers, some old floppy and hard drives.

Yes

  • where

Motors: Brushless Not very, these are hard to drive and often built into the circuit boards. May be most useful for the magnets in them. CD and VCR drives and players

Yes

  • where

Magnets, often quit strong and/or of odd configuration. Useful Hard drives, brushless motors. Microwave oven magnetron.

Yes

  • where

Potentiometers: trim Quite Audio equipment.

Yes

  • where

Relays Useful Microwave ovens.

Yes

  • where

Resistors: Power Useful Many different devices but usually not computers.

Yes

  • where

Resistors; ¼, ½ Watt Useless, leads too short

Yes

  • where

Ribbon Cables and Sockets

Yes. I ( russ_hensel ) have found a bunch or applications that may not be obvious, I will write it up soon, or contact me.

Computer

Sockets: DIP

Yes I ( russ_hensel ) I sometimes cut these up in various ways and epoxy to .1 inch perf. board to get special sockts for LED arrays....

Computers and many other components.

Stepper Driver Chips

Very if you can find some of the standard chips, I have found .....

  • Printers and Devices with stepper motors.

Three terminal regulators

Yes

  • Many different devices

Transistors: Power

Often useful, often can find specification from part number.

Audio equipment, TV's

Surface mount devices Useless, too hard to remove, too small to work with.

Yes

  • where

Transistor: Small Signal

Some use, but may be hard to identify which are useful as many use house part numbers. A few hours work gave me a couple of bucks worth of parts russ_hensel, probably not worth it.

Many different devices but usually not computers.

Transformers Inductors – Misc.

Test with ohm meter and audio oscillator.

TVs Audio Receivers.

Transformer Flyback transformer

Yes for high voltage – but can be dangerous.

TV's

Transformer: Line to Low voltage

Useful for making power supplies.

Audio equipment particularly receivers. Computer perifferals (sp ) but not computers.

what

Yes

  • where


Computers and computer mother boards

useful Almost all, although surface mount is driving them out.


-- Switch, PB pc board mount Very Many devices, often on a control panel separate from the main circuit board.


Meters Yes Some old audio equipment

Power supplies, any component with a power supply.

Inductors

Hall Effect Devices

cables

Sources -- What Can You Get Out Of Them

Computers Power supply is useful as a unit, or can be taken apart for transformer, caps, diodes, and similar. There are usually some LED and switches on the end of wires that plug into header blocks. They also may have CD DVD Floppy Drives see separate discussion. The connecting wires are often useful, sometimes taking the connectors off the mother board makes them more useful. Individual boards may be useful as they are. The mother board is not usually useful for its chips, most are too small and specialized for much use. Crystals may be found, not sure if frequencies are useful

Floppy Drives Often have stepper motor and Brush less motors. The old 5 ¼ drives are most likely to have reasonable power steppers. most of the chips then to be too small and specialized for much use.

Microwave Ovens Make sure you discharge high voltage capacitor prior to salvage, if you do not know how to do this find out firs. High voltage transformer ( dangerous ), high voltage capacitor and diode. Good magnets in the magnetron tube. Lots of micro switches. Small motor, motorized fan.

Printers Often have stepper motors. Plugs, jacks, power transistors, diodes. Gears, shafts and other mechanical components. Control panels may have led's and push button switches.

Stereos, boom boxes, radios Plugs, jacks, power transistors, diodes.

TV May not be a good salvage candidate: There are high voltage dangers and dangers from imploding picture tubes. Also when you are done there is often a disposal fee as the picture tube contains a few pounds of lead. Do not dispose of irresponsibly.

VCR DC motors, plugs, jacks, power transistors, diodes.

Salvage Techniques

Use a propane torch to salvage components from printed circuit boards ( from russ_hensel ).

First, this technique can be dangerous, in addition to possible burning yourself or burning your house down the components can emit dangerous fumes including fumes from the lead solder. Make sure you are operating carefully in a very well ventilated ( perhaps outdoor ) area. If you are not an adult have an adult approve of your procedure.

I use a propane touch with about a liter container of propane often used for plumbing work. I take the board and clamp it vertically in a vise. The torch is adjusted for about a 1 inch flame. Play the flame over the component leads while pulling on the component with a pair of pliers ( have several sizes available ). Work the component out and drop in a box. Move on to the next components. Some components can be pulled out with your fingers if you do not mind occasional burns, some can be pull out with your fingers but will burn you almost every time. If a component has heavy duty leads and light duty leads ( as some transistors that are connected to heat sinks do ) heat the heavy duty leads first. If the components has much plastic near the board ( for example ) headers, you may destroy the part. Practice will improve your technique. Keep your head out of the fumes. Try not to set the board on fire too often. When you do make sure you put it out. Do not leave the site of the work until the boards are cool. Even surface mount components can be removed, apply heat from the side away from the component, this will often ignite the board. This technique is at least an order of magnitude faster than using a soldering iron. Some people replace the torch with a paint removing heat gun, I have tried this but like the torch better.

Do the parts work after heating this way: for me almost always.