SFE Footprint Library
Jump to navigation
Jump to search
This is the holy grail for SFE. Each footprint is a custom layout. This library has been compiled over 5 years and 100s of man hours worth of work. If you are a student, please, enjoy and learn. If you are a professional, please buy something from www.sparkfun.com to help us out.
List of current fp's:
- 5-Lead DD PAK - Voltage regulator
- 0603 - This is the basic 0603 footprint. Use this or 0603 - OLD1
- 0603 - LED
- 0603 - OLD1 - Original, tight 0603 layout. Works great, very minimal
- 1206 - LED - This is a very revised, nice layout for 1206 LEDs including an expanded paste layer for a nice solid solder connection
- 3216 EIA-A - Perfect for 10uF tantulum caps
- 7343 EIA-D - Perfect for 100uF tantulum caps
- Antenna - 2.4GHz - This is the antenna found on the RF-24G devices. No guarantees it will impedance match
- Antenna - 2.45GHz - Chip antenna fp
- Antenna - SMA - Vertical mount SMA or RP-SMA connector
- Antenna - SMA - End Launch
- BGA-32 - 32 ball bga for the Analog Device's ADXRS MEMs gyros
- BlueRadio with Antenna - This is the FP for the Bluetooth module. No guarantees. It's a bit odd with restricted areas.
- CF Socket - Basic CF breakout. Start from here and make it fit your part
- CF Socket - Recommended - more silkscreen, wider solder pads
- CNZ1120 - Optical photo intr/sensor fp
- Coin Cell Holder 12mm - SMD
- Coin Cell Holder 20mm - PTH
- Connector Molex x - Vertical and right angle connectors with polarized connectors
- DB9 Headers - various DB9 connector FPs include PTH and end launch
- DIN-3 - DIN connector
- DIP connectors
- GM862 - Cellular module FP with antenna, pin1 indicator, and shield holes (proven, works great!)
- Headers - Various SIP 0.1" headers
- Lassen iQ - Couple FPs for the Lassen iQ with and w/o silkscreen lines (proven, works great)
- LCC8 - Special - Minimal FP for the ADXL series accelerometers from Analog Devices (proven, works great)
- LCD 16x2 - This is mechanical and electrical FP for 16x2 LCD from SFE. (proven, works great)
- LED Polarized - Simple T1, 5mm LED FP
- LED Polarized 3mm - 3mm LED fp, works ok. Hard to see silkscreen
- LFCSP - Recommended and modified FP for the newer ADXL32x series from Analog Devices. Recommended FP is proven and works great.
- microSD Socket - Proven, works great
- MLP-24 - Used for the nRF2401-ish ICs from Nordic. Proven, works great
- MLP-28 - Used for the CP210x USB ICs from SI Labs. Proven, works great
- PIC ICSP Mini - This is a custom FP by SFE. It's a in circuit serial programming jack that is 1.5mm pitch. Used to program just a bootloader onto a board without using up the space of a full sized programming header
- Power Jack - common barrel jacks with silk and mechanical layers
- Power Switch - Common SPDT switch, can be used for power or signal
- QFN-16 - Used for the MMA7260Q triple axis accelerometer. Works great but has some interesting keepout lines to keep vias out from under the IC
- QRD1114 - FP for the QRD1114 IR line sensor
- QUAD44 - TQFP package for the 16F877A IC
- Radial Caps - Various FPs for radial caps. Be sure your part matches the various dimensions.
- RJ11 - Jack for ICD or telephone
- Screw Terminal - 0.1" pitch screw terminal, two position version has two peg holes for structural stability
- SD-MMC Socket - Just what it sounds like
- SJ-2503A - 2.5mm stero jack
- SMA - Diode - Good 1A reverse polarized diode
- SMD Cap - SMD eletrolytics. Use at your own risk
- SOD-323 - Very small diode, good for signals
- SOIC - various soic FPs
- Solder Jumper - NC - Normally closed solder jumper. The paste layer is expanded so during reflow, extra paste is available so the jumper is shorted
- Solder Jumper - NO - Normall Open solder jumper. Paste layer is there, but not enough for a short
- Solder Switch - handy for SMD switches just using a soldering iron
- SOT-23 - Commom BJT footprint with various configuration. Check the datasheet for your particular part.
- SOT-23A - FP for popular small voltage regulators
- SOT-223 - Bigger 1A voltage regulators use this footprint like the LM1117
- SOT-457 - Transistor array FP
- SPDT Relay - Couple relay footprints
- SSOP - Various SSOP footprints
- Stencil Peg - This is an alignment hole for the Stencil-Alignment-System as well as a stand-off hole.
- Switch - Various momentary switch FPs. SMD, PTH, and Right Angle PTH
- Terminal Block - Various screw terminal blocks
- TO-92 - Various v-reg and PTH transistor FPs
- TO-220 - Various PTH FPs including LM317, LM7805, and heat sinked FPs
- TRF-24G - Popular FPs for the RF-24G 2.4GHz module
- Trim Pot - Couple trimpot FPs
- USB - Various USB connector FPs
- WEEE Icon - The european initiative to limit electronics trash. It's an silkscreen icon that looks like a trash can...
- Xtal-2 - Standard crystal FP
- Xtal-6 - SMD Watch crystal FP
- Xtal-SMD8 - SMD ceramic resonator FP
- Xtal-SMD9 - SMD quartz crystal FP