Experimenting with IR Remotes using a PIC running BoostC Project

From OpenCircuits
Jump to navigation Jump to search

Experimenting with IR Remotes using a PIC running BoostC Project

  • Name: Experimenting with IR Remotes using a PIC running BoostC Project
  • Status: done, until enhanced
  • Technology: PIC microcontroller, slavaged IR reciever, running with code in BoostC
  • Author: russ_hensel ( where you can find an email address to reach me )
  • Summary: A PIC16F877A project that reads IR remote controls. Runs with a PC running a terminal program.
  • Last revision: see page history.
  • Download: available, see section below.

This project describes just enough software and hardware to let you experiment with infra red remote controls to use as a jumping off point for a more complete project.

Platform: PIC16F877A using BoostC connected via rs232 to a PC running a terminal program. The PIC chip is supplemented with a slavaged IR reciever.

This code may be used as part of a user interface into a larger project. One pin supports all the buttons on a remote, and a universal remote is only about $10. and works remotely.

khaled ma'aitah Just

Command Interface

All commands ( except stop should be terminated with a carriage return ) Note that the command interface is not very smart, giving parameters that are out of range my blow the whole program up. If so reboot the PIC. Do not send a new command ( except stop ) until earlier commands have been completed ( actually you can get ahead some if you are careful )

Command Code Notes, PIC Response
Report version v<cr> Version of the PIC software something like:

Serial Stepper Test ver July 4 2008

Reset r<cr>

reset the counters and the log of the encoder. Response something like "Reset Count"

Log report l<cr> Report the log of data. A series of binary numbers, comma delimited.
Report on all parameters r Delimited by commas something like:
Position of the encoder p<cr> report the position of the encoder, and other counts of encoder activity.
Stop ! Should almost immediately stop long running commands of which there are currently none. Response Stopped.
Other, not understood commands xxx Responds with "!Bad Command = xxx" if the command is not understood.


Notes on terminal program set up.

  • Baud rate should be 19.2K 8N1
  • Most terminal programs can be set to treat a carriage return as a carriage return line feed. Do it.

Some terminal programs will not transmit in lower case ( all our commands are lower case ) unless specially set to do so. Set it to allow lower case.

Microcontroller Program

Design -- Polling Routine

The code in the download files is the project \IR.

If you look at the subroutine readIR( void ) you will see the heart of the IR receive. The routine loops each time checking to see if the output of the detector has changed. If it has not it adds one to the period, if it has it records the period and resets the period to 0. When the input goes quiet for a while it is taken as the end of the signal and we exit. Pretty simple.

The software logs the period of each transition at the input pin in units of the time around the receiving loop. The number of log entries is limited to about 100 due to memory limitations. Because the timing is in terms of times around the receive loop the code has been written to make this time ( roughly ) constant despite branches within the loop.

Control of readIR() is normally via an endless loop ( which the stop command breaks you out of ) which:

Listens for quiet on the IR signal, this stops us from starting to receive in the middle of a signal. Setting an interrupt to call readIR() on the next IR signal. Running readIR() Outputting the log or the received signal.

You can take the data from the log and put it in a spreadsheet to try to analyze what is going on. There is much information on IR protocols on the web.

One of my remotes seems to use the NEC protocol and I have added a version of readIR() to decode this signal, it is called readIRNec(). In this protocol there are basically two different low periods of the input, a short one is read as a 0 the long one as a 1. The code seems to work. I got the information on the protocol from [1].

I have tried to do a good job commenting the program, try reading them for more info. Comments on the comments, email me russ_hensel.

Note that the design blocks other activities in the software once the interrupt is triggered. This lasts about .1 seconds. I think the next itteration of the software should interrupt on each bit ( not just the starting bit ) and a timer should be used to time the bits. Then other tasks using either the main loop or other interrupts would not suffer much inpact. I will work on this at some future time ( update, I have an almost complete implementation Jan 9 09, should post fairly soon ). Do you have some code? Add your material here.

Some credit should be given to John Main [2] whose code I studied to aid in writing this.

Control of the software is via the serial communications library that I have described in other articles including Serial Communications Library -- BoostC and 16F877A. It yields a command driven interface with the following commands.

Commands

Command Action
! Stop whatever is running, like read ir and and read NEC. Then you can select a new command.
V<cr> Version of the software, responds something like: IR.c version = Dec 29 2008 b
I<cr> Read Ir Data in a loop without decoding. Generally turn log on or you will not see much in the way of results.
N<cr> Read Ir Data in a loop with NEC decoding. Generally turn log off unless you are debugging the decoding.

Response looks something like:

 exit waitForNoIR()
 IR Data = 10001011,01110100,00000011,11111100,
 IR Data hex = 8B,74,03,FC,
 XOR = 11111111,11111111
 
Ln<cr> Turn log report on with n=1, off with n=0. The log report gives the count of periods between all tranitions.

When reported the log will look something like:

 Lot Len =66,72,12,24,12,5,12,24,12,5,12,5,12,4,13,23,12,5,12,5,13,23,12,5,12,24,12,24,12,24,12,5,11,25,11,     
 6,11,6,11,6,11,6,11,5,12,5,12,5,12,24,12,24,12,24,12,24,12,24,11,25,11,25,11,24,12,5,12,

The first number is the number of items logged, the rest are the peiriods logged ( up to a max of about 100 )

<cr>


Design -- Interrupt Driven Routine

This is similar to the design above but the IR sections have be rewritten to use interrupts. For an explanation see: A Tutorial on PIC interrupts using BoostC including Example Programs The code in the download files is the project \IIR. This version is probably much better for use in a project than the non interrupt code, but was harder to code, and may be harder to understand. It only decodes the NEC ( inc Toshiba ) codes, others are logged for timing.

Notes on the NEC Decoding

Using the [] as I guide I guessed at the periods infolved in decoding 1 and 0's. The specification say that the odd numbered bytes should be the bitwize not of the next prior byte. I xor these together, if the decoding is right this should yeild a 1111111 which it seems to do. The button <1> decodes to 03 ( the third byte ). Each sucessively higher button goes up by 2. To see more codes, build the project. My transmitter was not actually a NEC but was a Toshiba which is supposed to be the same, perhaps it is. Test stuff yoursel before trusting the code too much.

Compiling

The zip file contains the entire source bootst project. Unzip into a directory and open in source boost. Set the target to 16F877A. See the comments in the program header for other setup before compiling. After compiling my compiler reports something like:

Memory Usage Report

  • RAM available:368 bytes, used:248 bytes (67.4%), free:120 bytes (32.6%),
  • Heap size:120 bytes, Heap max single alloc:95 bytes
  • ROM available:8192 words, used:1239 words (15.2%), free:6953 words (84.8%)

The program seems to be safely under the 2K free compiler limit.

Other Things to Try/Additions/Changes/Modification

  • The 877A is way overkill for this project unless you make it do a bit more. Note that only 1 input pin ( with interrupt capabability ) plus the serial lines are really used.
  • Make more interrupt driven.
  • Decode other brands of remotes.

Possibly useful links

This program uses my: Serial Communications Library -- BoostC and 16F877A

More information on serial communications with microcontrollers: Microcontroller Serial Communications Articles

A free terminal program, I like this much better than hyperterminal: Welcome to our Free Download/New Products Page! http://www.rs485.com/psoftware.html

BoostC – I think the free version is enough to compile the program: SourceBoost Technologies http://www.sourceboost.com/

Download

Both sets of code in IRCode.zip

Comment, Questions, Contributions?

Email me russ_hensel, or use the talk page for this topic. All feedback is welcome.