Difference between revisions of "Chemical Etchants"
(→Ferric Chloride: summary of etching chemistry)
(introduction, and brief safety note)
|Line 1:||Line 1:|
== Ferric Chloride ==
== Ferric Chloride ==
Revision as of 14:44, 28 April 2007
After masking off the parts of the copper-clad board you want to keep, you need to remove the parts you don't want to keep. This is usually done by chemically etching away the copper. There are a lot of different chemical techniques for doing this, each with its own advantages and drawbacks.
None of these chemicals is incredibly dangerous, but they can all be toxic or caustic, and should be treated with care. Eye protection and gloves are a very good idea. Before you start, make sure you know how dangerous each chemical is, and figure out what you will need to do if you spill it or get it on yourself. Washing with plenty of water is usually a good start. For some chemicals you may want to keep a neutralizing agent handy. An MSDS (Materials Safety Data Sheet) for the chemical will give you some basic information.
This is the most common hobbyist etchant. Ferric chloride, FeCl3, is a brownish substance. It's usually sold in a bottle (dissolved in water, perhaps with a little acid or peroxide) or as a powder (which you have to dissolve in water).
When in solution, ferric chloride is a ferric ion (Fe3+) and a chloride ion (Cl-). The ferric ion reacts with the metallic copper on the circuit board in a redox reaction, producing a ferrous ion (Fe2+) and cuprous or cupric (Cu1+ or Cu2+) copper. The chlorine is just along for the ride. The copper ion, unlike the metallic copper, is soluble, so it leaves the circuit board and goes into solution. The reaction products form a black sludge which settles to the bottom of the etching tank. After etching enough copper, all your Fe3+ is used up and your solution is full of Cu1+, and you need to get more etchant.
More environmentally friendly than ferric chloride. Can monitor the etching as initially clear new etchant solution turns blue from the copper ions.
Hydrochloric Acid and Hydrogen Peroxide
Dead simple etchant made from ordinary, store-bought chemicals. Has the advantage that it can be regenerated by bubbling oxygen/air through it, or by adding more H2O2. The used etchant also makes a great algecide/pH reducer for your pool (and a whole lot cheaper than that stuff they sell at the pool store).
What you need:
- 38% Hydrochloric Acid, HCl (available at finer pool supply stores as Muriatic Acid)
- 3% Hydrogen Peroxide, H2O2 (available from any drug store)
- Plastic or Glass Pans, Jars, and tongs (no metal)
- Mix your HCl and H2O2 1:1 in a non-metalic container, making sure to add the acid slowly to the H2O2. DO NOT ADD THE H2O2 TO THE ACID!!!
- After you've masked your board, dip it in the solution and constantly agitate. You should notice a dark green cloud start to come from the board almost immedately which quickly dissapears or turns lighter as it gets further from the surface of the board.
- Etching should take about 10min depending on the temperature and how well you agitated the etchant. When all of the copper is gone, dip in water to wash off any stray etchant and stop the reaction.
- When done etching, save used etchant in a non-metalic container and mark clearly its contents.
- If your etchant has become a dark, murky green color, add a little bit of H2O2 or bubble air/O2 through the solution to regenerate it back to a light, transparent green color.
See links at bottom for more information on the chemistry and some pictures of the process.
Flushing used etchant down the drain is a bad idea (and usually illegal) because copper ion is toxic. The usual recommended way to dispose of hobbyist amounts of etchant is to convert it to a solid somehow and dispose of the solid in the trash.
- Kepro Circuit Systems Removal of Copper and Persulfate from Spent Sodium Persulfate Etchant by Precipitation