Motor driver

There are many kinds of motor drivers:

Servo motor controller
Stepper motor controller
DC motor controller ("brushed")
AC motor controller ("brushless")
... (todo: fill in the other kinds) ...

A DC motor controller that is 'reversible' generally uses an 'H bridge'. This 'H-bridge' uses four output drivers in a configuration that resembles an H where the load is the cross bar in the middle. The lines on either side of the load (the downward strokes in the H) represent a series connection of a pull-up driver and a pull-down driver. This allows each terminal of the load to be connected to either the positive supply rail, or the negative supply rail. This allows a positive, negative or zero voltage difference across the load. This load voltage is then utilized to provide the desired control required of the motor. The various combinations can give a 'forwards' torque on a DC motor, a 'backwards' torque on the same motor, can allow the motor to free-wheel (without any applied torque) or can provide a locking of the motor such that it resists any attempt to rotate it.

A single phase AC motor is generally driven in the same way as a DC motor, however instead of operating the motor drive as a constant DC voltage (in either the 'forward' or 'reverse' direction) the AC motor is driven by an approximation to a sinewave. This approximation is created using the H bridge and driving it with a PWM input such that both the positive and negative voltage periods are the same. This is normally achieved either using a sawtooth waveform compared against a sine wave reference, or is done using a lookup table in a microcontroller.

A similar method is used to drive multiphase (3-phase) AC motors, however instead of just using an H bridge, only a half H bridge is used per phase (3 half-bridges). Each phases half bridge is then driven in the same manner as for the single phase motor, with a phase difference between the phases as appropriate.

Most stepper motor controllers uses 2 independent H bridges (4 half-bridges) for the 2 independent coils of a stepper motor. Each possible state (one bridge driving current one way, the other way, or free-floating) of both bridges gives 4 "full steps", 4 "half-steps" between the full steps. The "microstepping" motor controllers use PWM to gradually change in a sine-wave-like manner from adjacent full-steps and half-steps.

((fill in more details here...))

External links

A random collection of semi-related links (please prune out the irrelevant ones):

H-Bridge by Bob Blick
the Open Source Motor Controller Project
LiniStepper $30 each; Open Source! Circuit Diagram, PCB (Board) Layout, and PIC Software all available. Nice photos of the LiniStepper at http://www.piclist.com/techref/io/stepper/linistep/lini_bld.htm .
"Design of a High Current Bipolar Stepper Motor Driver"
H-Bridge Fundamentals An in-depth article on the design of Mosfet H-Bridges
PMinMO.com Open Source circuits and information on stepper motor controllers]
ePanorama ePanorama Motor Control page
"Electronic Design of DC Motor Drives" has detailed schematics and PCB layout for a system that has a PC send commands through the serial port to a Microchip PICmicro, which does PWM control of 2 H bridges. Each half-bridge uses a IRF9530N (100V 14A pfet plus flyback diode) and a IRF530 (IRF530NPBF: 100V 17A nfet plus flyback diode), driven by a small transistor inverter based on a BD135 npn, for a total of 12 discrete transistors.
OpenServo wiki -- developing a digital servo motor that accepts "Go to position X" commands and also more complex curves, and returns actual servo position, speed, voltage and power consumption.
MOSFETs and MOSFET drivers
L297 stepper motor controller + L298 dual full-bridge driver: for driving one (4-wire) bipolar stepper motor (2 A); direction and step inputs; half-stepping; on-chip PWM chopper limits current. external diodes are required (preferably Shottky). (Both chips come in through-hole and SMT versions)
L298 dual full-bridge driver can also be used to drive 2 independent DC motors (2 A each); external diodes are required (preferably Shottky). L293D is similar, but only rated up to 1 A, 36 V.
SparkFun: EasyDriver v3 Stepper Motor Driver based on A3967 microstepping driver chip; up to 750mA, 30 V.
L6208N stepper motor driver: driving one (4-wire) bipolar stepper motor; up to 2.8 A, 52 V. direction and step inputs. PWM current control; includes internal diodes. over-current and thermal protection. half-stepping. MC3479 stepper motor drive is similar, but only rated up to 350 mA, 16 V.
Nanotec sells microstepping stepper motor driver chips (the IMT-901, IMT-902, and IMT-903) and assembled stepper motor driver modules.
Reprap: Arduino has a long side-thread on various motor driver chips.
lots of stepper motor driver chips
Critical Velocity sells DC motor speed controllers and stepper motor controllers.
Geckodrive sells DC motor speed controllers and stepper motor controllers.

astronomy telescopes use motor drivers:

scope drive webring: a selection of Websites that display procedures to equip amateur telescopes with homemade computerized drive systems
"scopedrive" for automating telescopes

Robots use motor drivers.

Glendale robotics club (Glendale CA)
"H bridges" by David Cook at the ROBOT ROOM(TM)
"A Second Generation Speed Controller" by Chuck McManis. Can handle 200 amps continuously. Uses two PIC16F628 chips driving sixteen IRF1010E FETs: "(I like to call it a "two way SMP microkernel with serial cluster interconnect" as that sounds better than "a couple of PICs with their serial ports wired together" :-)"

Motor driver

External links

Robots use motor drivers.

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools