Serial Communications (RS232) in BoostC - Revision history

Russ hensel: /* Compiling the Program */

2009-08-27T14:36:03Z

Compiling the Program

2009-08-24T02:37:17Z

File Structure and Pre Processing

2009-08-23T02:34:25Z

News

2009-08-20T00:14:09Z

News

2009-08-20T00:07:06Z

Download

2009-08-20T00:06:09Z

Compiling the Program

2009-08-20T00:00:35Z

File Structure and Pre Processing

2009-07-31T00:13:22Z

Fuse.h

2009-07-30T23:55:22Z

Hardware for the Program

2009-07-29T00:07:58Z

Features

@@ Line 120: / Line 120: @@
 The code for the library and the demo program is in one zip file ( called DemoSerial.zip, see Download below ). Unzip into a directory of its own.  Open the project file SerialDemo.__c and compile with the source boost C compiler.  The source files are SerialDemo.c SerialDemo.h.....
 Before compiling make sure you change the target PIC to whatever you are using and check the #defines to see that they are right for your code  Project.h has some of the most important.  See File Structure and Pre Processing below.
 I also use a non standard location for my compiler and you may need to adjust for your setup.  Check Options ->  Tools -> and make sure the setting there corresponds to you set up.
 Before you actually try it with real hardware review your clock frequency and baud rate settings etc. .... in the code.
 ==== File Structure and Pre Processing ====

@@ Line 131: / Line 131: @@
 ==== File Structure and Pre Processing ====
-I am working on a standard sturcture for my programs to make them adapatable to different configurations including processor, clock speed etc.  For you to make sense of this you need to understand a bit about the C preprocessor esp. #include and #define.
+I am working on a standard sturcture for my programs to make them adapatable to different configurations including processor, clock speed etc.  For you to make sense of this you need to understand a bit about the C preprocessor esp. #include and #define.  Note that I use #warning for messages about compile options, they are not warnings and normall begin with "Info >>".
 ===== mainfile.c =====

@@ Line 13: / Line 13: @@
 === News  ===
-This page is still draft, but near final, will work on it if you have questions or I am otherwise motivated.
+*This page is still draft, but near final, will work on it if you have questions or I am otherwise motivated.
 === Features  ===

@@ Line 13: / Line 13: @@
 === News  ===
-This page is still draft
+This page is still draft, but near final, will work on it if you have questions or I am otherwise motivated.
 === Features  ===

@@ Line 238: / Line 238: @@
 === Download ===
-Zip file here ...comming....  I may have more recent versions, email me if you want to check [[russ_hensel]]
+Zip file here [http://home.comcast.net/~russ_hensel/OC/DemoSerial_v5.zip DemoSerial_v5.zip]  I may have more recent versions, email me if you want to check [[russ_hensel]]
 === Projects using this Library ===

← Older revision		Revision as of 00:06, 20 August 2009
Line 123:		Line 123:

	Before compiling make sure you change the target PIC to whatever you are using and check the #defines to see that they are right for your code Project.h has some of the most important. See File Structure and Pre Processing below.		Before compiling make sure you change the target PIC to whatever you are using and check the #defines to see that they are right for your code Project.h has some of the most important. See File Structure and Pre Processing below.
		+
		+	I also use a non standard location for my compiler and you may need to adjust for your setup. Check Options -> Tools -> and make sure the setting there corresponds to you set up.

	Before you actually try it with real hardware review your clock frequency and baud rate settings etc. .... in the code.		Before you actually try it with real hardware review your clock frequency and baud rate settings etc. .... in the code.

@@ Line 142: / Line 142: @@
 ===== Fuse.h =====
-contains the fuse settings.  These are determined from the stuff set up in project.h.  Fuse.h should be included only once, this should be in the mainfile right after the include for project.h.  Fuse.h should not be modified for an individual project, you should be able to make additions so it will work with all projects.
+Contains the fuse settings.  These are determined from the stuff set up in Project.h.  Fuse.h should be included only once, this should be in the mainfile right after the include for Project.h.  Fuse.h should not be modified for an individual project, you should be able to make additions so it will work with all projects.
 ===== Library Files =====

← Older revision		Revision as of 23:55, 30 July 2009
Line 114:		Line 114:


−	[[Stepper Motor Tester]] has a Eagle file that will work for this demo. You can drop the stepper driver chip. Even the level shifter can be dropped if you use a cable with a level shifter. The circuit is an easy project to do on a proto board. Another project, with very similiar hardware, but no ~~loevel~~ shifter is [[PIC based Stepper Motor Dancing Analog Clock]]	+	[[Stepper Motor Tester]] has a Eagle file that will work for this demo. You can drop the stepper driver chip. Even the level shifter can be dropped if you use a cable with a level shifter. The circuit is an easy project to do on a proto board. Another project, with very similiar hardware, but no level shifter is [[PIC based Stepper Motor Dancing Analog Clock]]

	=== Compiling the Program ===		=== Compiling the Program ===

@@ Line 31: / Line 31: @@
 <!-------------------------------->
 |-valign="top"
-|Code includes preprocessing for changing the processor or baud rate
+|Code includes preprocessing for changing the processor and ( coming soon baud rate )
 |uses multiple files and #define
 <!-------------------------------->
 |-valign="top"