Arduino Socket - Revision history

Russ hensel: /* Introduction */

2018-02-03T17:12:24Z

Introduction

Russ hensel: /* Boards */

2018-02-02T22:28:32Z

Boards

Russ hensel: /* Solder */

2018-02-02T22:28:08Z

Solder

Russ hensel: /* Done */

2018-02-02T22:27:31Z

Done

Russ hensel: /* Parts */

2018-02-02T18:12:36Z

Parts

Russ hensel at 16:08, 2 February 2018

2018-02-02T16:08:28Z

Russ hensel at 15:58, 2 February 2018

2018-02-02T15:58:55Z

Russ hensel: Created page with "= Introduction = There is an old tradition in electronics, if a part is expensive or inclined to blow, make it replaceable by putting it in a socket. Sometimes this goes to..."

2018-02-01T21:11:19Z

Created page with "= Introduction = There is an old tradition in electronics, if a part is expensive or inclined to blow, make it replaceable by putting it in a socket. Sometimes this goes to..."

New page

= Introduction =

There is an old tradition in electronics, if a part is expensive or inclined to blow, make it replaceable by putting it in a socket. Sometimes this goes too far as with final circuits that are still on a proto board where everything is in a socket. But if we are using small arduinos like the nano we more or less treat them as a component and putting them in a socket is a good idea. As far as I know sockets for these parts are not made, and the pins on an arduino are not really the normal pins for sockets. However we can make what we need on a strip board or PCB by using 2 rows of female headers. Pictures tell the rest of the story.

Note that this is an article started by Russ Hensel, see "http://www.opencircuits.com/index.php?title=Russ_hensel#About My Articles" '''About My Articles'''

= Parts =

[[Category:Arduino/RaspberryPi]]

← Older revision		Revision as of 17:12, 3 February 2018
Line 5:		Line 5:
	Note that this is an article started by Russ Hensel, see "http://www.opencircuits.com/index.php?title=Russ_hensel#About My Articles" '''About My Articles'''		Note that this is an article started by Russ Hensel, see "http://www.opencircuits.com/index.php?title=Russ_hensel#About My Articles" '''About My Articles'''

		+	An almost identical write up of this topic can be found at: [[https://www.instructables.com/id/Socket-to-Your-Arduino/ Socket to Your Arduino: 6 Steps (with Pictures)]]

	= Parts =		= Parts =

@@ Line 11: / Line 11: @@
 In this case I am using stripboard, but any PCB board with .1 inch spacing should be good.
-[[Image:Sboard1.JPG|400px]]
+[[Image:Sboard1.JPG|400px]]  [[Image:Sboard2.JPG|400px]]
 == Arduino ==

@@ Line 39: / Line 39: @@
 Finish soldering:
-[[Image:Solder.JPG|400px]]
+[[Image:Solder.JPG|400px]]  [[Image:Solder dun.JPG|400px]]
 == Done ==

@@ Line 46: / Line 46: @@
 == Done ==
-[[Image:Mont it.JPG|400px]]
+[[Image:Mont it.JPG|400px]]  [[Image:Finished0.JPG|400px]]  [[Image:Finished1.JPG|400px]]
 <!--------------start hidden ------------------
@@ Line 52: / Line 54: @@
 [[Image:x.JPG|400px]]
-[[Image:x.JPG|400px]]
+[[Image:Finished1.JPG|400px]]
-[[Image:x.JPG|400px]]
+[[Image:Finished0.JPG|400px]]
 <!-------------- end hidden --------------------->

@@ Line 8: / Line 8: @@
 = Parts =
+== Boards ==
 [[Image:Sboard1.JPG|400px]]
 [[Image:Sboard2.JPG|400px]]
 [[Image:Nano.JPG|400px]]
-* [[Image:Fheader.JPG|400px]]
+Cut it with a fine tooth saw.  I cut through the middle of a pin which is sacrificed.
-* [[Image:Cut header.JPG|400px]]
+== Solder ==
 [[Image:Tack.JPG|400px]]
 [[Image:Solder.JPG|400px]]
@@ Line 31: / Line 44: @@
 [[Image:Solder dun.JPG|400px]]
 [[Image:Mont it.JPG|400px]]

← Older revision		Revision as of 16:08, 2 February 2018
Line 23:		Line 23:


−	[[Image:~~con1~~.~~png~~\|400px]]	+	[[Image:Tack.JPG\|400px]]


−	[[Image:~~con1~~.~~png~~\|400px]]	+	[[Image:Solder.JPG\|400px]]
		+
		+
		+	[[Image:Solder dun.JPG\|400px]]
		+
		+
		+	[[Image:Mont it.JPG\|400px]]
		+
		+	<!--------------start hidden ------------------
		+
		+	[[Image:x.JPG\|400px]]
		+
		+	[[Image:x.JPG\|400px]]
		+
		+	[[Image:x.JPG\|400px]]
		+
		+	<!-------------- end hidden --------------------->

← Older revision		Revision as of 15:58, 2 February 2018
Line 7:		Line 7:

	= Parts =		= Parts =
		+
		+
		+
		+	[[Image:Sboard1.JPG\|400px]]
		+
		+	[[Image:Sboard2.JPG\|400px]]
		+
		+	[[Image:Nano.JPG\|400px]]
		+
		+
		+	* [[Image:Fheader.JPG\|400px]]
		+
		+
		+	* [[Image:Cut header.JPG\|400px]]
		+
		+
		+	[[Image:con1.png\|400px]]
		+
		+
		+	[[Image:con1.png\|400px]]
		+
		+
		+


	[[Category:Arduino/RaspberryPi]]		[[Category:Arduino/RaspberryPi]]